- Boilers
- Gas boiler
F10
Vaillant F.10 on a gas boiler: flow sensor short circuit
Risk level
Medium
Proceed carefully and stop if the check is unclear.
Urgency
Medium
Quick answer
Vaillant F.10 means a heating flow sensor short circuit. It is an electrical fault in the sensor or its wiring: do not open the boiler, take a photo of the code and call an authorised professional.
Safety first
Stop and check this first
- If you smell gas: do not operate switches, sockets, doorbells or phones, no flames or smoking, open doors and windows, close the meter valve and the appliance gas valve if you can, warn neighbours without using the bell, leave the building and call the gas company from outside. That is what Vaillant asks.
- Do not remove, bypass or tamper with sensors or safety devices: Vaillant forbids it and there is mains voltage inside.
Safe checks you can perform
- Constant or intermittent code
- Fill pressure on the display
- Sensor check by the technician
Leave these tasks to a qualified professional
- Do not attempt this professional task: NTC sensor reading
- Do not attempt this professional task: Connector and harness check
- Do not attempt this professional task: Readings in the diagnostics menu
What a technician must be able to justify
Technician visit
These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.
These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.
NTC sensor reading
What they doThe technician measures the flow sensor with a multimeter and compares the value with the real temperature using the maker's table.
They must show youthe measured value against the expected one.
In writingthe reading and any part replaced.
Connector and harness check
What they doThe technician checks the NTC connector and the harness to the board, looking for breaks or contact with the housing.
They must show youthe connector and cable checked.
In writingthe repair done.
Readings in the diagnostics menu
What they doAfter the repair, the technician reads actual flow and return temperatures in the diagnostics menu (D.040 and D.041) and the fault memory.
They must show youthe readings on screen.
In writingthe running test.
Before accepting a part or repair
Nothing has been shown yet. Do not accept a part swap based on the code alone.
Follow these steps
Note: Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.
Constant or intermittent code
- Who:
- you.
- How:
- take a photo of the display and note whether F.10 is always there or only at times. Vaillant says to call an authorised professional when an F.xx message appears.
- Result that matters:
- whether the fault is constant or intermittent.
- If it is constant:
- call the authorised professional.
- If it comes and goes:
- tell the technician; a loose contact fits better than a broken part.
- Evidence to keep:
- photos of the code with date and time.
Evidence: Vaillant ecoTEC plus VMW ..6/5-5, instrucciones de instalación y mantenimiento 0020244991_01 · Vaillant ecoTEC plus VM, VMW y VMI ..6/5-5, instrucciones de funcionamiento 0020243851_02
Fill pressure on the display
- Who:
- you.
- How:
- with the system cold, press twice the key the manual names for showing pressure and read the value. Vaillant asks for 1.0 to 2.0 bar.
- Result that matters:
- whether pressure is within that range.
- If it is below 0.8 bar:
- top up with the filling valve as Vaillant describes and bleed the radiators; tell the technician.
- If it is in range:
- lack of water does not explain F.10.
- Evidence to keep:
- a photo of the display with the pressure.
Evidence: Vaillant ecoTEC plus VM, VMW y VMI ..6/5-5, instrucciones de funcionamiento 0020243851_02
Sensor check by the technician
- Who:
- technician authorised by Vaillant.
- How:
- checks the flow sensor, the connector, the cable harness and the board, as Vaillant's table says.
- Result that matters:
- where the signal is cut or shorted.
- If the sensor reads wrong:
- it is replaced.
- If the sensor reads correctly:
- connector, cable and board are checked.
- Evidence to keep:
- a report of what was measured and replaced.
Vaillant reserves inspection, maintenance, repair and gas settings for an authorised professional: the user does not open the boiler.
Evidence: Vaillant ecoTEC plus VMW ..6/5-5, instrucciones de instalación y mantenimiento 0020244991_01
Still not solved
If the error persists, stop here. See what the technician must do and show you.
Where this code applies
A code is meaningful only inside the right product and version context.
Primary scope
- System
- Boilers
- Brand
- Vaillant
- Product type
- Gas boiler
Known code variants
- A10 Ferroli
- Bluehelix F10
- cocina LG F10 puerta
- ecoTEC F.10
- Error F10 Ferroli
- Error F10 Saunier Duval
- Error F10 Vaillant
- F 10
- Ferroli F 10
- lavadora Miele anomalía F10
- LG F-10 horno
- LG F10 door lock
- LG F10 horno
- LG horno F10 bloqueo
- LG oven F-10
- LG oven F10 error
- LG range F10
- Miele F10 entrada de agua
- Miele F10 water inlet
- Miele lavadora F10
- Miele washer F10
- Miele washing machine fault F10
- Saunier Duval F.10
- ThemaFast Condens F.10
- Vaillant F.10
What it means
In the ecoTEC plus table, F.10 is the flow sensor short circuit. Vaillant gives a faulty or short circuited flow temperature sensor as the cause and says to check the NTC connector, cable harness, cable and housing, circuit board and NTC sensor. The NTC sensor measures heating water temperature on the flow and the board uses it to control the burner; without a valid reading the boiler protects itself. The code does not say whether the sensor, connector, cable or board is at fault.
Warnings and stop conditions
- Criticalsource verified
If you smell gas: do not operate switches, sockets, doorbells or phones, no flames or smoking, open doors and windows, close the meter valve and the appliance gas valve if you can, warn neighbours without using the bell, leave the building and call the gas company from outside. That is what Vaillant asks.
Evidence: Vaillant ecoTEC plus VM, VMW y VMI ..6/5-5, instrucciones de funcionamiento 0020243851_02
- Mediumsource verified
Do not remove, bypass or tamper with sensors or safety devices: Vaillant forbids it and there is mains voltage inside.
Evidence: Vaillant ecoTEC plus VM, VMW y VMI ..6/5-5, instrucciones de funcionamiento 0020243851_02
Symptoms and causes
Probable causes · in order
- Flow NTC sensor faultyPossible
If the technician measures the sensor out of range with the connector properly fitted, the sensor is the cause.
Evidence: Vaillant ecoTEC plus VMW ..6/5-5, instrucciones de instalación y mantenimiento 0020244991_01
- Cable or housing shortedPossible
If a bare cable touches the housing or the connector is damp, the board sees a short even if the sensor is fine.
Evidence: Vaillant ecoTEC plus VMW ..6/5-5, instrucciones de instalación y mantenimiento 0020244991_01
- Circuit boardLess common
Vaillant lists it; it is only considered if the sensor and wiring measure correctly.
Evidence: Vaillant ecoTEC plus VMW ..6/5-5, instrucciones de instalación y mantenimiento 0020244991_01
Virtual technician
Does F10 still appear after these checks?
Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.
Sources and technical references
- 1
Vaillant ecoTEC plus VMW ..6/5-5, instrucciones de instalación y mantenimiento 0020244991_01
Vaillant · 2017 · manual
- 2
Vaillant ecoTEC plus VM, VMW y VMI ..6/5-5, instrucciones de funcionamiento 0020243851_02
Vaillant · 2017 · manual
Was this entry useful?