- Appliances
- Washing machines
E8
Beko E8 on a washing machine: may not be taking in water
Risk level
Low
Usually safe to check without specialist tools.
Urgency
Low
Quick answer
On Beko washers such as the BM1WU3741W and BM1WU3721W, E8 means the machine may not be taking in water. Turn on the taps, make sure there is no water outage, straighten the inlet hose and close the door properly.
Safety first
Stop and check this first
- This code table is the one for the Beko BM1WU3741W and BM1WU3721W; on other Beko models the same code may mean something else, so check your model's manual.
- Beko says the water inside can reach 90 ºC: clean the pump filter only once it has cooled and with the machine unplugged.
Safe checks you can perform
- Taps and water supply
- Inlet hose
- Door closing
- Inlet filters and pump filter
Leave these tasks to a qualified professional
- Do not attempt this professional task: Failure list readout and test wash
- Do not attempt this professional task: Check of the inlet valve and its internal filter
What a technician must be able to justify
Technician visit
These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.
These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.
Failure list readout and test wash
What they doAfter the repair, the technician reads the failure list again with auxiliary buttons 1 and 2 and runs a wash to see it takes in water without E8.
They must show youthe failure list with no new E8 and the machine taking in water.
In writingthe test carried out, the programme used, the result and the date.
Check of the inlet valve and its internal filter
What they doThe technician checks the filter at the end of the water intake valve at the rear and tests the valve against Beko's specification.
They must show youthe condition of the valve filter and the result of the valve test.
In writingthe cause, the part replaced with its part number and the reason.
Before accepting a part or repair
Nothing has been shown yet. Do not accept a part swap based on the code alone.
Follow these steps
Note: Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.
Taps and water supply
- Who:
- you, without opening the machine.
- How:
- check that the tap feeding the washer hose is fully open and open another tap in the house to see whether there is water.
- Result that matters:
- ruling out a closed tap or a supply outage.
- If the tap was off or the house has no water:
- turn it on or wait for the supply and repeat the wash.
- If there is water and the tap is open:
- check the inlet hose.
- Evidence to keep:
- photo of the tap and a note of whether the house had water.
Evidence: Beko Washing Machine User Manual BM1WU3741W · Beko Washing Machine User Manual BM1WU3721W
Inlet hose
- Who:
- you.
- How:
- follow the inlet hose from the tap to the back of the machine; check it is firmly connected and not folded, and straighten any kink.
- Result that matters:
- water being able to pass without restriction.
- If it was folded or loose:
- correct it and start the programme again.
- If it is straight and well connected:
- go on to the door and filters.
- Evidence to keep:
- photo of the hose before and after straightening.
Evidence: Beko Washing Machine User Manual BM1WU3741W
Door closing
- Who:
- you.
- How:
- close the loading door firmly, making sure no laundry is caught, and check that the machine shows the door locked when the programme starts.
- Result that matters:
- the door locking so that filling can begin.
- If the door was not closing properly:
- once closed, the machine takes in water and washes.
- If it closes and locks but still gets no water:
- clean the filters.
- Evidence to keep:
- note of whether the door locked before and after.
Evidence: Beko Washing Machine User Manual BM1WU3741W
Inlet filters and pump filter
- Who:
- you, with the machine unplugged and the water cooled.
- How:
- turn off the taps and clean the filter at the end of the hose by the tap; then clean the pump filter following the manual section on draining water and cleaning the pump filter.
- Result that matters:
- no filter being blocked by dirt or debris.
- If there was dirt and the test wash works after cleaning:
- it was a filter.
- If the filters were clean:
- run one more wash and, if E8 returns, call Beko's service.
- Evidence to keep:
- photo of the filters and of any debris removed.
Evidence: Beko Washing Machine User Manual BM1WU3741W
Still not solved
If the error persists, stop here. See what the technician must do and show you.
Where this code applies
A code is meaningful only inside the right product and version context.
Primary scope
- System
- Appliances
- Brand
- Beko
- Product type
- Washing machines
Known code variants
- AEG E8
- AEG E822
- AEG hob E8
- Baxi heat pump E8
- Baxi HP40 E8
- Baxi HP50 E8
- Beko BM1WU E8 code
- Beko lavadora E8
- Beko washer E8
- Beko washing machine E8 not taking water
- Bosch Compress E8
- Bosch E8 caudal de agua
- Bosch E8 water flow
- Bosch heat pump E8
- código E8 Beko BM1WU
- Compress 2000 AWF E8
- CS2000AWF E8
- E08
- E 8
- E822
- E8xx
- E:8
- error E8 aerotermia Bosch
- Gree E8
- Junkers E8
- lavadora Beko E8 no coge agua
- placa AEG E8
What it means
In Beko's manuals for the BM1WU3741W and BM1WU3721W, E8 is in the failure list you read with the machine off by holding auxiliary function buttons 1 and 2: after a 3-2-1 countdown and the total number of washes, any stored failure codes appear. Beko explains it as the machine may not be taking in water and says to check the taps, water outage, inlet hose, pump filter and door lock. The code does not prove the inlet valve is faulty; if it persists after those checks, the service is the next step.
Warnings and stop conditions
- Loweditorial warning
This code table is the one for the Beko BM1WU3741W and BM1WU3721W; on other Beko models the same code may mean something else, so check your model's manual.
Evidence: Beko Washing Machine User Manual BM1WU3741W · Beko Washing Machine User Manual BM1WU3721W
- Mediumsource verified
Beko says the water inside can reach 90 ºC: clean the pump filter only once it has cooled and with the machine unplugged.
Evidence: Beko Washing Machine User Manual BM1WU3741W
Symptoms and causes
Probable causes · in order
- Tap off or water outageCommon
Beko says to turn on the taps and make sure there is no water outage; opening another tap rules this out first.
Evidence: Beko Washing Machine User Manual BM1WU3741W · Beko Washing Machine User Manual BM1WU3721W
- Inlet hose folded or badly connectedCommon
The manual says to check the water inlet hose connection and straighten any fold; you can see it behind the machine.
Evidence: Beko Washing Machine User Manual BM1WU3741W
- Dirty inlet filtersPossible
There are filters at the end of the water intake valve and at the end of the hose where it meets the tap; dirt there slows the water.
Evidence: Beko Washing Machine User Manual BM1WU3741W
- Door not lockedPossible
The troubleshooting table lists a loading door that is not closed as a cause of no water intake; the E8 solution says to close the front cover and make sure it is locked.
Evidence: Beko Washing Machine User Manual BM1WU3741W
- Fault in the appliance water inletPossible
If all of the above is fine and E8 returns on a new wash, Beko says to call the service to check the inlet.
Evidence: Beko Washing Machine User Manual BM1WU3741W
Virtual technician
Does E8 still appear after these checks?
Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.
Sources and technical references
- 1
Beko Washing Machine User Manual BM1WU3741W
Beko plc · 2024 · manual
- 2
Beko Washing Machine User Manual BM1WU3721W
Beko plc · 2024 · manual
Was this entry useful?