- Appliances
- Dishwashers
I50
Electrolux i50 on a dishwasher: wash motor or pump fault
Risk level
Medium
Proceed carefully and stop if the check is unclear.
Urgency
Medium
Quick answer
Electrolux groups i50 and the whole i51 to i5F family as a wash motor or circulation pump fault. Switch off at the mains for a minute, clean the filters and sump of foam and debris, and try a programme. If it returns, call a technician.
Safety first
Stop and check this first
- The wash motor runs on mains power and sits under the tub next to water: do not remove the kickplate or base to inspect it.
Safe checks you can perform
- One minute reset
- Filters and sump
- Test programme
Leave these tasks to a qualified professional
- Do not attempt this professional task: Wash motor diagnosis
- Do not attempt this professional task: Full wash after the repair
What a technician must be able to justify
A technician is coming
These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.
These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.
Wash motor diagnosis
What they doWith the appliance disconnected, the technician inspects the wash motor, its connection and the control that powers it, and measures against Electrolux specification.
They must show youthe measurement against the specification or the removed part.
In writingwhat was measured, the result and the reference of any replaced part.
Full wash after the repair
What they doThe technician lets a programme finish and checks no i5 code returns.
They must show youthe finished programme with no code.
In writingthe test and the date.
Before accepting a part or repair
Nothing has been shown yet. Do not accept a part swap based on the code alone.
Checks and evidence, step by step
Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.
- 1
One minute reset
No special tools
Procedure
- Who:
- you.
- How:
- switch the dishwasher off at the mains, wait around one minute and switch it back on, as Electrolux says.
- Result that matters:
- whether the code is still there.
- If it is gone:
- clean the filters before the next wash anyway.
- If it is still there:
- clean the filters and sump before calling.
- Evidence to keep:
- a photo of the exact code, for example i53 or i5C.
Evidence: Dishwasher displays error code i50 · Electrolux dishwasher displays an error code: causes and solutions
- 2
Filters and sump
No special tools
Procedure
- Who:
- you.
- How:
- with the appliance unplugged, clean all filters and clear foam and debris from the sump.
- Result that matters:
- a sump with no foam or debris.
- If there was foam or debris and it washes well afterwards:
- that was the cause.
- If it was clean:
- the likely cause is the motor or pump.
- Evidence to keep:
- a photo of the sump before cleaning.
Evidence: Dishwasher displays error code i50
- 3
Test programme
No special tools
Procedure
- Who:
- you.
- How:
- run a suitable programme and listen for washing (water circulating) or a stop with the code.
- Result that matters:
- whether the cycle runs normally.
- If it finishes with no code:
- that solves it.
- If an i5 code returns:
- do not keep running programmes; call a technician.
- Evidence to keep:
- the point in the cycle where the code appeared.
Evidence: Dishwasher displays error code i50
Where this code applies
A code is meaningful only inside the right product and version context.
Primary scope
- System
- Appliances
- Brand
- Electrolux
- Product type
- Dishwashers
Known code variants
- AEG dishwasher i50
- AEG Fehler i50
- AEG Geschirrspüler i50
- AEG i50 error
- AEG lavastoviglie i50
- AEG lavavajillas i50
- AEG lave-vaisselle i50
- code erreur AEG i50
- Electrolux dishwasher i50
- Electrolux i50
- error AEG i50
- error i50 lavavajillas Electrolux
- errore AEG i50
- I50
- i50 AEG dishwasher
- i50 AEG Geschirrspüler
- i50 AEG lavastoviglie
- i50 AEG lavavajillas
- i50 AEG lave-vaisselle
- i51
- i52
- i53
- i54
- i55
- i56
- i57
- i58
- i59
- i5A
- i5C
- i5H
What it means
According to Electrolux, every code in the i50 family (i50 to i5F, including i5H) relates to a wash motor or pump malfunction: the appliance detects a problem with water circulation during the wash. Electrolux asks for a one minute mains reset and clean filters and sump, because foam and debris affect circulation. If the code persists, the motor is an internal mains powered part: a technician inspects it. The code does not say whether the motor, its wiring or the control is at fault.
Warnings and stop conditions
- Mediumeditorial warning
The wash motor runs on mains power and sits under the tub next to water: do not remove the kickplate or base to inspect it.
Evidence: Dishwasher displays error code i50
Symptoms and causes
Probable causes · in order
- Foam or debris in the sumpPossible
Electrolux asks you to look for foam and debris first. If there was some and the programme washes without a code after cleaning, the pump was not faulty.
Evidence: Dishwasher displays error code i50
- Wash motor or pump faultCommon
This is the cause Electrolux gives for the whole i50 family. It becomes the suspect if the code returns with a clean sump and after the reset.
Evidence: Dishwasher displays error code i50
Virtual technician
Does I50 still appear after these checks?
Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.
Sources and technical references
- 1
Dishwasher displays error code i50
Electrolux · official_doc
- 2
Electrolux dishwasher displays an error code: causes and solutions
Electrolux · official_doc
Was this entry useful?