- Appliances
- Dishwashers
I60
Electrolux i60 on a dishwasher: heating problem
Risk level
Medium
Proceed carefully and stop if the check is unclear.
Urgency
Medium
Quick answer
Electrolux uses i60 (also i61, i69 or i6C) when the water in the tub is too hot or the temperature sensor has failed. Check the inlet water does not exceed 60 °C at the connection, unplug, clean the filters and sump, and try a programme.
Safety first
Stop and check this first
- The heater and temperature sensor run on mains power next to water: do not open the appliance to measure them; it is a technician job.
Safe checks you can perform
- Inlet water temperature
- Reset with clean filters
- Test programme
Leave these tasks to a qualified professional
- Do not attempt this professional task: Sensor and heater measurement
- Do not attempt this professional task: Heating test after the repair
What a technician must be able to justify
A technician is coming
These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.
These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.
Sensor and heater measurement
What they doWith the appliance disconnected, the technician measures the temperature sensor and heating circuit against Electrolux specification.
They must show youthe measured values against the specification.
In writingwhat was measured, the result and the reference of any replaced part.
Heating test after the repair
What they doThe technician lets a heated programme finish and checks i60 does not return.
They must show youthe finished programme with no code.
In writingthe test and the date.
Before accepting a part or repair
Nothing has been shown yet. Do not accept a part swap based on the code alone.
Checks and evidence, step by step
Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.
- 1
Inlet water temperature
No special tools
Procedure
- Who:
- you or your plumber.
- How:
- see whether the dishwasher is connected to hot water and how hot that water is at the connection; a thermometer at a nearby tap on the same line gives a guide.
- Result that matters:
- no more than 60 °C at the connection point.
- If it is above 60 °C:
- that may be the cause; ask the plumber to adjust it.
- If it is on cold water or below 60 °C:
- the inlet is ruled out.
- Evidence to keep:
- the thermometer reading and where you took it.
Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C
- 2
Reset with clean filters
No special tools
Procedure
- Who:
- you.
- How:
- unplug the dishwasher, check the filters and sump, clean all filters and clear foam and debris.
- Result that matters:
- a clean sump before testing again.
- If there was foam or debris:
- clean it and test; that may be enough.
- If it was clean:
- the likely cause is the sensor or heating.
- Evidence to keep:
- a photo of the sump and the code.
Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C · Electrolux dishwasher displays an error code: causes and solutions
- 3
Test programme
No special tools
Procedure
- Who:
- you.
- How:
- plug in, choose a suitable programme and let it finish; at the end, touch the dishes to see whether they are warm.
- Result that matters:
- whether the cycle finishes with no code.
- If it finishes:
- that solves it.
- If i60 returns:
- call a technician.
- Evidence to keep:
- the result and whether the dishes came out cold.
Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C
Where this code applies
A code is meaningful only inside the right product and version context.
Primary scope
- System
- Appliances
- Brand
- Electrolux
- Product type
- Dishwashers
Known code variants
- AEG dishwasher i60
- AEG Fehler i60
- AEG Geschirrspüler i60
- AEG i60 error
- AEG lavastoviglie i60
- AEG lavavajillas i60
- AEG lave-vaisselle i60
- code erreur AEG i60
- Electrolux dishwasher i60
- Electrolux dishwasher not heating
- Electrolux i60
- error AEG i60
- error i60 lavavajillas Electrolux
- errore AEG i60
- I60
- i60 AEG dishwasher
- i60 AEG Geschirrspüler
- i60 AEG lavastoviglie
- i60 AEG lavavajillas
- i60 AEG lave-vaisselle
- i61
- i69
- i6C
- lavavajillas Electrolux no calienta
What it means
For Electrolux, i60 and its variants mean the water inside the appliance is too hot or the temperature sensor has malfunctioned; the usual symptom is no heating or poor drying. Electrolux asks you to check the inlet water is not above 60 °C at the connection point, reset by unplugging and clean the filters and sump of foam and debris. If it persists, the heating system runs on mains power: a technician inspects it. The code does not separate heater, sensor or control.
Warnings and stop conditions
- Mediumeditorial warning
The heater and temperature sensor run on mains power next to water: do not open the appliance to measure them; it is a technician job.
Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C
Symptoms and causes
Probable causes · in order
- Inlet water too hotPossible
If the dishwasher is connected to hot water, Electrolux says it must not exceed 60 °C at the connection. You check it at the house plumbing without opening the appliance.
Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C
- Foam or debris in the sumpPossible
Electrolux includes cleaning the filters and clearing foam in the reset. If there was some and it then heats with no code, this was it.
Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C
- Temperature sensor or heating faultCommon
This is the cause Electrolux gives for abnormal temperature. It becomes the suspect if the code returns with correct inlet water and a clean sump.
Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C
Virtual technician
Does I60 still appear after these checks?
Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.
Sources and technical references
- 1
Dishwasher displays error code i60 / i61 / i69 / i6C
Electrolux · official_doc
- 2
Electrolux dishwasher displays an error code: causes and solutions
Electrolux · official_doc
Was this entry useful?