- Networks
- Mesh Wi-Fi routers
LUZ-MORADA-FIJA
Linksys Velop LUZ-MORADA-FIJA: solid purple setup indicator
Risk level
Low
Usually safe to check without specialist tools.
Urgency
Medium
Quick answer
On Linksys Velop mesh Wi-Fi systems (WHW, MX, and MR series), a solid purple light (LUZ-MORADA-FIJA) means the node is in its factory default state and ready for setup, or that a child node has not yet been detected and added in the Linksys app.
Safety first
Stop and check this first
- Do not reset the parent node (the node connected to your modem) when troubleshooting a child node; if a factory reset is needed to get a solid purple light, reset only the child node.
Safe checks you can perform
- Place the solid purple child node within 10 ft of the online parent node with Bluetooth on
- Run Add Another Node in the Linksys app and tap Add more nodes if not detected
- Check whether DFS is enabled or if you are mixing Cognitive and Intelligent Mesh
Leave these tasks to a qualified professional
- Do not attempt this professional task: Use the 5-Button Push method or CA Router Setup tab if the Linksys app is unavailable
- Do not attempt this professional task: Contact Linksys support if a compatible child node remains stuck on solid purple
What a technician must be able to justify
Technician visit
These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.
These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.
Use the 5-Button Push method or CA Router Setup tab if the Linksys app is unavailable
What they doIf the Linksys mobile app is unavailable or cannot complete discovery after placing the child node within 10 feet and disabling DFS, use the official 5-Button Push method or the CA Router Setup tab in the web interface.
They must show youChild node LED turning solid blue and appearing online in the mesh network.
In writingPairing method used and final placement location where the child node maintains a solid blue light.
Contact Linksys support if a compatible child node remains stuck on solid purple
What they doIf both nodes belong to the compatible Intelligent Mesh lineup, are in the same room within 10 feet, and the child node still fails to transition from solid purple to solid blue, contact Linksys support.
They must show youModel and serial numbers of the parent and child nodes, DFS status, and setup results within 10 feet.
In writingLinksys support ticket number and firmware or hardware resolution.
Before accepting a part or repair
Nothing has been shown yet. Do not accept a part swap based on the code alone.
Follow these steps
Note: Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.
Place the solid purple child node within 10 ft of the online parent node with Bluetooth on
- Who:
- Person adding the child node using the Linksys mobile app.
- How:
- Confirm the parent node connected to your modem has a solid blue light, place the child node in the same room no more than 10 feet away, wait for its solid purple light, and make sure your phone is on the Linksys Wi-Fi network with Bluetooth enabled.
- Result that matters:
- Child node showing solid purple within 10 feet of the online parent node.
- If the child node displays a solid purple light next to the parent node, open the Linksys app menu and start Add Another Node.
- If the child node light is solid red or blinking red instead of solid purple, factory reset only the child node (never the parent node).
- Evidence to keep:
- Photo of the solid purple child node positioned in the same room as the solid blue parent node.
Evidence: Understanding the light behavior of your Linksys Mesh WiFi system · Adding a child node to your existing Linksys Velop Intelligent Mesh WiFi system using the Linksys app
Run Add Another Node in the Linksys app and tap Add more nodes if not detected
- Who:
- Network administrator in the Linksys app dashboard.
- How:
- Tap the top-left menu icon in the Linksys app > Set up a New Product > Add Another Node > To extend my Wi-Fi with a new child node > Node light is solid; if the child node is not detected, move it closer in the same room and tap Add more nodes to try again.
- Result that matters:
- LED transitioning from blinking purple (setup in progress) to solid blue (connected to the network).
- If the child node light turns solid blue, relocate the node to its final spot and wait for the light to turn solid blue again.
- If the node still fails to add within 10 feet of the parent node, check DFS settings and model compatibility.
- Evidence to keep:
- Screenshot of the child node added confirmation in the Linksys app.
Evidence: Linksys MX5300, MX4000 series, and MX8500 series light behaviors · Adding a child node to your existing Linksys Velop Intelligent Mesh WiFi system using the Linksys app
Check whether DFS is enabled or if you are mixing Cognitive and Intelligent Mesh
- Who:
- Administrator reviewing Wi-Fi settings and model numbers.
- How:
- Check your Linksys app Wi-Fi settings to see if Dynamic Frequency Selection (DFS) is turned on when adding a child node that may not support DFS, and verify you are not trying to add a Velop Cognitive Mesh child node to an Intelligent Mesh system.
- Result that matters:
- Confirmation of channel compatibility and mesh product family match.
- If turning off DFS allows the solid purple child node to pair and turn solid blue, keep DFS disabled for that node.
- If the child node is a Cognitive Mesh model paired with an Intelligent Mesh parent, they are not backward compatible.
- Evidence to keep:
- Exact model numbers of the parent and child nodes plus DFS setting status.
Evidence: Adding a child node to your existing Linksys Velop Intelligent Mesh WiFi system using the Linksys app
Still not solved
If the error persists, stop here. See what the technician must do and show you.
Where this code applies
A code is meaningful only inside the right product and version context.
Primary scope
- System
- Networks
- Brand
- Linksys
- Product type
- Mesh Wi-Fi routers
Known code variants
- Child node not detected solid purple
- Luz violeta fija Linksys Velop
- Node is ready for setup Linksys
- Node light is solid purple Linksys
- Nodo listo para configurar Linksys
- Solid purple light Linksys Velop
What it means
In Linksys's official light behavior guides for Linksys Mesh systems (articles 62-en and 443-en) and child-node setup instructions (article 67-en), a solid purple indicator means the node has finished booting in its factory state and is ready for setup (while blinking purple indicates setup is in progress). When a child node stays on solid purple or is not detected during setup, it is typically placed too far from the parent node, blocked by disabled Bluetooth, or affected by DFS or series compatibility rules. Other models may differ, and this light alone never proves a faulty hardware part.
Warnings and stop conditions
- Higheditorial warning
Do not reset the parent node (the node connected to your modem) when troubleshooting a child node; if a factory reset is needed to get a solid purple light, reset only the child node.
Evidence: Adding a child node to your existing Linksys Velop Intelligent Mesh WiFi system using the Linksys app
Symptoms and causes
Probable causes · in order
- Node is in its factory default state waiting to be added in the Linksys appCommon
The unit is brand new or was recently factory reset and has not yet been paired through Set up a New Product > Add Another Node in the Linksys app.
Evidence: Understanding the light behavior of your Linksys Mesh WiFi system · Linksys MX5300, MX4000 series, and MX8500 series light behaviors · Adding a child node to your existing Linksys Velop Intelligent Mesh WiFi system using the Linksys app
- Child node placed more than 10 ft away from the parent node or Bluetooth disabledCommon
During setup, the child node is located more than 10 feet from the parent node or in another room, or Bluetooth is turned off on the mobile device running the Linksys app.
Evidence: Adding a child node to your existing Linksys Velop Intelligent Mesh WiFi system using the Linksys app
- DFS enabled on the network or incompatible Cognitive Mesh and Intelligent Mesh mixPossible
Linksys notes that enabling Dynamic Frequency Selection (DFS) can prevent a non-DFS child node from joining, and Linksys Velop Cognitive Mesh child nodes are not backward compatible with Intelligent Mesh systems.
Evidence: Adding a child node to your existing Linksys Velop Intelligent Mesh WiFi system using the Linksys app
Virtual technician
Does LUZ-MORADA-FIJA still appear after these checks?
Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.
Sources and technical references
- 1
Understanding the light behavior of your Linksys Mesh WiFi system
Linksys · 2026 · official_doc
- 2
Linksys MX5300, MX4000 series, and MX8500 series light behaviors
Linksys · 2026 · official_doc
- 3
Linksys · 2026 · official_doc
Was this entry useful?