- Appliances
- Dryers
E80
AEG dryer E80: cycle-selector fault
Risk level
Medium
Proceed carefully and stop if the check is unclear.
Urgency
High
Quick answer
E80 means the cycle selector is between programmes or the selector/software branch is not reading a valid programme. Preserve the full display and model, then use the physical selector position, selected programme name and whether E80 clears when firmly aligned to choose the next branch before any part or paid repair.
Safety first
Stop and check this first
- Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Safe checks you can perform
- Capture the decision evidence
- Run the one discriminating check
- Stop at the result boundary
Leave these tasks to a qualified professional
- Do not attempt this professional task: Evidence-led AEG handoff for E80
What a technician must be able to justify
Technician visit
These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.
These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.
Evidence-led AEG handoff for E80
What they doA qualified technician should test selector position, knob coupling, selector feedback, software or control, using the exact model/PNC and the recorded result for the physical selector position, selected programme name and whether E80 clears when firmly aligned.
Before accepting a part or repair
Nothing has been shown yet. Do not accept a part swap based on the code alone.
Follow these steps
Note: Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.
Capture the decision evidence
Photograph E80, the complete message and model/PNC. Record the failed programme stage and the physical selector position, selected programme name and whether E80 clears when firmly aligned. Do not clear the history repeatedly.
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dryer E80 cycle-selector error
Run the one discriminating check
Turn the dryer off, place the selector firmly on one documented programme—not between detents—then perform one 30-second reset and start that programme once.
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dryer E80 cycle-selector error
Stop at the result boundary
Clearing when aligned proves selector position. E80 returning on a firm detent selects selector feedback/software/control; forcing or spraying the knob is not a repair. If the same result returns after this one controlled pass, stop rather than chaining resets or cycles.
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dryer E80 cycle-selector error
Still not solved
If the error persists, stop here. See what the technician must do and show you.
Where this code applies
A code is meaningful only inside the right product and version context.
Primary scope
- System
- Appliances
- Brand
- AEG
- Product type
- Dryers
Known code variants
- AEG asciugatrice E80
- AEG dryer E80
- AEG E80 error
- AEG Fehler E80
- AEG secadora E80
- AEG sèche-linge E80
- AEG Trockner E80
- Bosch E80 lavadora
- Bosch E80 washer
- Bosch washer E80 error
- code erreur AEG E80
- E-80
- E80 AEG asciugatrice
- E80 AEG dryer
- E80 AEG secadora
- E80 AEG sèche-linge
- E80 AEG Trockner
- error AEG E80
- error E80 lavadora Bosch
- errore AEG E80
What it means
AEG's official French support documents E80 on the dryer as follows: the cycle selector is between programmes or the selector/software branch is not reading a valid programme. The exact model manual controls compatibility; the same code on another appliance can mean something else.
Warnings and stop conditions
- Highsource verified
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dryer E80 cycle-selector error
Symptoms and causes
Probable causes · in order
- Official AEG meaningConfirmed
AEG's official French support documents E80 on the dryer as follows: the cycle selector is between programmes or the selector/software branch is not reading a valid programme. The exact model manual controls compatibility; the same code on another appliance can mean something else.
Evidence: AEG France — dryer E80 cycle-selector error
- What still has to be separatedPossible
selector position, knob coupling, selector feedback, software or control
Evidence: AEG France — dryer E80 cycle-selector error
Virtual technician
Does E80 still appear after these checks?
Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.
Sources and technical references
- 1
AEG France — dryer E80 cycle-selector error
AEG France · 2026 · official_doc
Was this entry useful?