- Appliances
- Dishwashers
I10
AEG dishwasher i10: water-inlet fault
Risk level
Medium
Proceed carefully and stop if the check is unclear.
Urgency
High
Quick answer
i10 means water is not entering, or the inlet flow is too low. Preserve the full display and model, then use whether a household tap delivers about 10 litres in one minute and whether the tub begins filling to choose the next branch before any part or paid repair.
Safety first
Stop and check this first
- Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Safe checks you can perform
- Capture the decision evidence
- Run the one discriminating check
- Stop at the result boundary
Leave these tasks to a qualified professional
- Do not attempt this professional task: Evidence-led AEG handoff for i10
What a technician must be able to justify
A technician is coming
These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.
These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.
Evidence-led AEG handoff for i10
What they doA qualified technician should test tap, hose, inlet valve, flow detection or model-specific filling control, using the exact model/PNC and the recorded result for whether a household tap delivers about 10 litres in one minute and whether the tub begins filling.
Before accepting a part or repair
Nothing has been shown yet. Do not accept a part swap based on the code alone.
Checks and evidence, step by step
Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.
- 1
Capture the decision evidence
No special tools
Procedure
Photograph i10, the complete message and model/PNC. Record the failed programme stage and whether a household tap delivers about 10 litres in one minute and whether the tub begins filling. Do not clear the history repeatedly.
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dishwasher i10/i11 water-inlet error
- 2
Run the one discriminating check
No special tools
Procedure
Open the tap fully, confirm household flow and inspect only the visible inlet hose for a kink. Clean an accessible inlet filter only if the exact manual describes it.
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dishwasher i10/i11 water-inlet error
- 3
Stop at the result boundary
No special tools
Procedure
No flow at the tap belongs to the household supply. Good tap flow but no fill belongs to the appliance inlet branch; close the tap if water appears where it should not. If the same result returns after this one controlled pass, stop rather than chaining resets or cycles.
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dishwasher i10/i11 water-inlet error
Where this code applies
A code is meaningful only inside the right product and version context.
Primary scope
- System
- Appliances
- Brand
- AEG
- Product type
- Dishwashers
Known code variants
- AEG dishwasher AL5
- AEG dishwasher C1
- AEG dishwasher F1
- AEG dishwasher i10
- AEG dishwasher i11
- AEG Fehler i10
- AEG Geschirrspüler AL5
- AEG Geschirrspüler C1
- AEG Geschirrspüler F1
- AEG Geschirrspüler i10
- AEG Geschirrspüler i11
- AEG i10 error
- AEG lavastoviglie AL5
- AEG lavastoviglie C1
- AEG lavastoviglie F1
- AEG lavastoviglie i10
- AEG lavastoviglie i11
- AEG lavavajillas AL5
- AEG lavavajillas C1
- AEG lavavajillas F1
- AEG lavavajillas i10
- AEG lavavajillas i11
- AEG lave-vaisselle AL5
- AEG lave-vaisselle C1
- AEG lave-vaisselle F1
- AEG lave-vaisselle i10
- AEG lave-vaisselle i11
- code erreur AEG i10
- Electrolux dishwasher i10
- Electrolux i10
- error AEG i10
- error i10 lavavajillas Electrolux
- errore AEG i10
- I10
- i10 AEG dishwasher
- i10 AEG Geschirrspüler
- i10 AEG lavastoviglie
- i10 AEG lavavajillas
- i10 AEG lave-vaisselle
- i11
What it means
AEG's official French support documents i10 on the dishwasher as follows: water is not entering, or the inlet flow is too low. The exact model manual controls compatibility; the same code on another appliance can mean something else.
Warnings and stop conditions
- Highsource verified
Stop immediately for water near electricity, smoke, burning smell, abnormal heat, damaged cable or repeated breaker trips. Close the water tap when a leak is possible; sealed water, heat and mains circuits are professional-only.
Evidence: AEG France — dishwasher i10/i11 water-inlet error
Symptoms and causes
Probable causes · in order
- Official AEG meaningConfirmed
AEG's official French support documents i10 on the dishwasher as follows: water is not entering, or the inlet flow is too low. The exact model manual controls compatibility; the same code on another appliance can mean something else.
Evidence: AEG France — dishwasher i10/i11 water-inlet error
- What still has to be separatedPossible
tap, hose, inlet valve, flow detection or model-specific filling control
Evidence: AEG France — dishwasher i10/i11 water-inlet error
Virtual technician
Does I10 still appear after these checks?
Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.
Sources and technical references
- 1
AEG France — dishwasher i10/i11 water-inlet error
AEG France · 2026 · official_doc
Was this entry useful?