ErrorBase
Independent technical referenceOfficial site
  • Appliances
  • Dishwashers

I60

Zanussi i60 on a dishwasher: heating or temperature fault

Verified with sources1 sourceReviewed Oct 4, 2026
Technician coming? See the 3 steps they must show you
Open dishwasher showing its racks
Yelderberry (talk)CC BY-SA 4.0Image source

Risk level

Medium

Proceed carefully and stop if the check is unclear.

Urgency

Medium

Quick answer

On a Zanussi dishwasher, i60, i61, i69 or i6C mean a heating problem: water too hot or a temperature sensor fault. Check the inlet water does not exceed 60 °C, reset the appliance and clean the filters and sump.

Safety first

Stop and check this first

  • Water and electricity: the heater runs on mains voltage in contact with water; do not open the appliance or touch it.

Safe checks you can perform

  • Inlet water temperature
  • Reset with filter cleaning
  • Do not touch the heater

Leave these tasks to a qualified professional

  • Do not attempt this professional task: Temperature sensor measurement
  • Do not attempt this professional task: Heating check
  • Do not attempt this professional task: Test programme

What a technician must be able to justify

Technician visit

These are the steps they must carry out and show you. Tick them as they work: if steps are skipped, do not accept a part swap.

These are not instructions for opening or handling the equipment yourself. They are the checks that should support a technical conclusion.

  1. Temperature sensor measurement

    What they doWith the appliance disconnected from the mains, the engineer measures the temperature sensor with a multimeter and checks its connector.

    They must show youthe measured value against the manufacturer's specification.

    In writingthe measured value, the conclusion and, if the sensor is replaced, its part number.

  2. Heating check

    What they doThe engineer checks the heater and whether it receives voltage when the control calls for heat.

    They must show youthe heater measurements and the voltage it receives.

    In writingwhat was measured, which part is replaced, its part number and why.

  3. Test programme

    What they doAfter the repair, the engineer runs a heated programme and checks it finishes with no code.

    They must show youthe programme finished with no code and hot dishes.

    In writingthe programme tested, the result and the date.

Before accepting a part or repair

Nothing has been shown yet. Do not accept a part swap based on the code alone.

Follow these steps

Note: Follow the documented order. An error code identifies the affected system, but it does not prove by itself which part has failed.

  1. Inlet water temperature

    No special tools

    Who:
    you, without opening the appliance.
    How:
    look under the sink to see whether the fill hose comes from the hot or the cold supply. If it is the hot supply, check your boiler or water heater temperature.
    Result that matters:
    whether water reaching the connection can exceed 60 °C.
    If it can exceed 60 °C:
    Zanussi advises against it; ask the installer to correct it and try again.
    If it is on cold or below 60 °C:
    rules out the inlet water; move on to the reset.
    Evidence to keep:
    a photo of the connection the hose uses and your boiler or water heater temperature.

    Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

  2. Reset with filter cleaning

    No special tools

    Who:
    you, with the appliance unplugged.
    How:
    unplug, clean all filters, clear foam and debris from the sump, plug back in and run a suitable programme.
    Result that matters:
    whether the programme starts and finishes normally.
    If it finishes fine:
    Zanussi says the problem is solved.
    If the code returns:
    book a visit to check the sensor and heating.
    Evidence to keep:
    a photo of the code and the sump before cleaning.

    Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

  3. Do not touch the heater

    Tools required

    Who:
    engineer; you only keep the appliance unplugged.
    How:
    do not open the appliance to look at the heater or sensor. Note whether dishes came out cold or wet in recent washes.
    Result that matters:
    a clear description of the symptom for the engineer.
    If they came out cold:
    fits no heating; tell the engineer.
    If they came out hot but wet:
    tell them too; it points towards drying.
    Evidence to keep:
    a note of the symptom and the programmes it happened on.

    The heater and its sensor run on mains voltage in contact with water; only an engineer measures or replaces them.

    Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

Still not solved

If the error persists, stop here. See what the technician must do and show you.

Where this code applies

A code is meaningful only inside the right product and version context.

Primary scope

System
Appliances
Brand
Zanussi
Product type
Dishwashers

Known code variants

  • AEG dishwasher i60
  • AEG Fehler i60
  • AEG Geschirrspüler i60
  • AEG i60 error
  • AEG lavastoviglie i60
  • AEG lavavajillas i60
  • AEG lave-vaisselle i60
  • code erreur AEG i60
  • Electrolux dishwasher i60
  • Electrolux dishwasher not heating
  • Electrolux i60
  • error AEG i60
  • error i60 lavavajillas Electrolux
  • error i60 lavavajillas Zanussi
  • errore AEG i60
  • I60
  • i60 AEG dishwasher
  • i60 AEG Geschirrspüler
  • i60 AEG lavastoviglie
  • i60 AEG lavavajillas
  • i60 AEG lave-vaisselle
  • i61
  • i69
  • i6C
  • lavavajillas Electrolux no calienta
  • lavavajillas Zanussi no calienta
  • Zanussi dishwasher i60
  • Zanussi dishwasher i61
  • Zanussi dishwasher i69
  • Zanussi dishwasher i6C
  • Zanussi dishwasher not heating
  • Zanussi i60 error
  • Zanussi i60 lavavajillas
  • Zanussi i61 lavavajillas
  • Zanussi i69 lavavajillas
  • Zanussi i6C lavavajillas

What it means

Zanussi puts i60 down to water inside the appliance being too hot or a temperature sensor fault. The control reads water temperature to run the heater and drying, so the symptom is no heating or drying. Zanussi asks that inlet water not exceed 60 °C at the connection and that filters and sump are cleaned. The code does not prove the heater or sensor has failed; that needs measuring.

Warnings and stop conditions

  • Mediumeditorial warning

    Water and electricity: the heater runs on mains voltage in contact with water; do not open the appliance or touch it.

    Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

Symptoms and causes

Probable causes · in order

  • Inlet water too hotPossible

    Fits if the dishwasher is connected to the hot supply. Zanussi sets 60 °C at the connection as the limit.

    Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

  • Temperature sensorPossible

    Zanussi names it as a cause. Confirmed by measuring the sensor with the appliance open, an engineer's job.

    Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

  • Foam or debris in filters and sumpPossible

    Fits if you see dirt or foam at the bottom. Zanussi includes cleaning them in the reset before a visit.

    Evidence: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

Virtual technician

Does I60 still appear after these checks?

Answer a few questions to narrow down the likely cause and the safest next action. Guidance only - it never replaces a professional.

Start diagnosis

Sources and technical references

  1. 1

    Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussi

    Zanussi (Electrolux Group) · official_doc

Sources: Dishwasher displays error code i60 / i61 / i69 / i6C | Zanussireviewed 2026-10-04 · verified

Was this entry useful?